[2 Pack] S10 Plus Screen Protector Compatible for Samsung Galaxy S10 Plus / S10+, Fingerprint ID

(10 customer reviews)

$42.99

SKU: s10+uvtg Category:

Description

[2 Pack] S10 Plus Screen Protector Compatible for Samsung Galaxy S10 Plus / S10+, Fingerprint ID

Product Description

galaxy s10+ screen protector

Warm Tips:

  1. must keep it in the indoor without any ultraviolet rays or sunshines when installing tempered glass.(Because the UV glue is easy to be solidified under the ultraviolet rays, the installation will be failed)
  2. Make sure to keep the phone on the leved surface
  3. Make sure to use the guide label to stick the earpiece speaker hole for avoiding the glue spilling into it,and remove the guide sticker when the film is affixed.
  4. Must keep the screen surface clean with our wipes before dropping the glue.
  5. Please follow the installation video and make sure the glue squeezed out with long line shape (if there are bubbles, need puncture it. for the Galaxy S10 and S10 plus, the glue will be little bit less near to the fingerprint, so easy and better to read the fingerprint sensor).
  6. Please don’t raise or press this screen protector when you installing, otherwise, will be fail. (the failed installation tempered glass could show like those situations: “cloudy “/”splotchy”/“air bubble”/”glue pattern” and so on…)
  7. Need make sure use this UV light to dry the screen glue and keep it for at least 60 seconds, until the glue is full dry. ( in order to keep the glue fit better,must irradiate the four corners and all of edges above 120 seconds again)
  8. For Galaxy S10 and S10 plus, after installation the tempered glass, highly suggest you re-scan your fingerprint
  9. While scanning the fingerprint, press little hard and scan fingerprint with all angles
  10. When scanning or unlocking fingerprint, must keep finger dry and clean
  11. Each tempered glass film only need one uv glue.

Product Features:

  1. Compatible with:Samsung galaxy S10+
  2. 100% Brand New
  3. High Quality
  4. Purpose: offer all-round protection for your galaxy s10+ screen
  5. Full Coverage: The full Coverage film will seamlessly cover Galaxy s10+ screen and Dust-proof and waterproof,and effectively protect it from scratched by keys, coins or any other hard substances, offer all-round protection for your galaxy s10+.
  6. 6X Shock-Resistance & 9H Hardness: The full Coverage screen protector is made of 9H hardness tempered glass, which provides 6X shock resistances for your galaxy s10+. The protector will protect your cellphone efficiently from all direction.
  7. Facial Recognition& Supremely Transparent: This screen protector supports facial recognition, you can unlock your cellphone with sensitive facial recognition easily.
  8. Ultra Thin& Supremely Transparent: Featuring 0.2mm ultra-thin and 99.9% transparency, the tempered glass film will present the true to life color on the samsung galaxy s10+ entire screen;Responsive touch feedback ensures quick APP launches and smooth video playing/gaming.
  9. Easy Installation & Anti-Fingerprint: Easy to install, no experience is needed when apply the protector on the screen. Coated with hydrophobic and oleophobic clear layers, the glass protects against fingerprints caused by sweat and oil residue, keeping the screen pristine all day.

Package included:

  1. 2x UV Full Coverage Curved Edge Tempered Glass Film for samsung galaxy s10+
  2. 2x UV glue
  3. 2x Dry wipes
  4. 2x Dry wipes
  5. 4X Guide Sticker
  6. 2X Dust-absorber

galaxy s10+ screen protector features

Product Features:

Optical adhesive full adsorption design, no edge warp, no bubble and no gaps fit, dustproof and waterproof, Give you great touch feel without stickers

 

 

Installation Guide

STEP1 STEP 2 STEP 3

STEP 1 Clean the screen surface

  1. Remember to put the guide stickers on the ear speaker and charging port to avoid the liquid spilling inside.
  2. Clean the screen surface with the wet wips.
  3. Clean the screen surface with the dry wips.

STEP 2 Clean the dust

  1. Before installing tempered glass, must keep it in the indoor without any ultraviolet rays or sunshines (Because the UV glue is easy to be solidified under the ultraviolet rays, the installation will be failed) .
  2. Make sure to keep the phone on the leved surface.
  3. Stick out dust & dirts with sticker.

STEP 3 Drop the UV glue

Drop the UV glue in the middle of the screen
  1. Please follow the installation video and make sure the glue squeezed out with long line shape(if there are bubbles, need puncture it).
  2. For the Galaxy S10 and S10 plus, the glue will be little bit less near to the fingerprint, so easy and better to read the fingerprint sensor.

 

STEP 5

STEP 4 Installing the tempered glass

Align the curved screen with the corresponding posltion of the phone and cover the tempered glass,Don’t move or raise or press, wait for it to fit automatically.

================================================

*****The most important thing: Please don’t raise or press this screen protector, otherwise, this installation will fail. (the failed installation tempered glass could show like those situations: “cloudy “/”splotchy”/“air bubble”/”glue pattern” and so on…)

 

STEP 5

STEP 5 Drying the UV glue

  1. Use this UV light to dry the screen glue and keep it for at least 60 seconds, until the glue is full dry. ( in order to keep the glue fit better,must irradiate the four corners and all of edges above 120 seconds again).
  2. After drying, remove the guide sticker.

================================================

*****The most important thing: Please don’t raise or press this screen protector when you drying this glue with the UV light, otherwise, this installation will fail. (the failed installation tempered glass could show like those situations: “cloudy “/”splotchy”/“air bubble”/”glue pattern” and so on…)

 

STEP 6

STEP 6 Scan the fingerprint

  1. For Galaxy S10 and S10 plus, after installation the tempered glass, highly suggest you re-scan your fingerprint.
  2. While scanning the fingerprint, press little hard and scan fingerprint with all angles.
  3. When scanning or unlocking fingerprint, must keep finger dry and clean.

 

Additional information

Item Weight

3.2 ounces

Shipping Weight

3.2 ounces (View shipping rates and policies)

ASIN

B07Q33TQCD

10 reviews for [2 Pack] S10 Plus Screen Protector Compatible for Samsung Galaxy S10 Plus / S10+, Fingerprint ID

  1. Shawn Ron

    Update: Very Very Important and UsefulI saw some users complainted that the fingerprint scanner didn’t work after installing the tempered glass, but mine worked so great, here i share my experience as below:** After finishing installation the screen protector tempered glass, Must record your fingerprint again, because the second time to re-scan fingerprint can improve fingerprint sensor much better** When you scan fingerprint, please press little bit hard, and what’s more, use DIFFERENT ANGLES to scan your fingerprint** Before scanning or unlocking fingerprint, please keep your finger dry and clean without any water or dust or other dirty things.If you note above three tips, I believe your fingerprint scanner will be working so great like me. Wish my tips can help you to avoid fingerprint sensor failureSince this is the UV liquid glue tempered glass, gave me different installing experience with the normal ones before. It’s my first time being able to install it. Watch the video a few times and the read the guide installation carefully where need to be more noting. Then it was easy to install and avoid all failures happened!The 1st most important thing is that Before installation screen protector, please do it In The Indoor (Don’t be closed to window or sinshines, because the UV glue is super easy to be dry under the ultraviolet rays, then the glue can’t cover the whole screen to cause installation failure)The 2nd most important thing is that keep your phone on a very flat surface, Or the glue easy to flow everywhere of your phone and mess upThe 3rd most important thing is that putting the guide sticker on the ear speaker and charging port to avoid the glue spillingThe 4th most inportant thing is that DON’T move, lift and press the glass and just wait the glue fit it automatically and then use the UV light to irradiate the glass above 60 seconds, And re-irradiate All of Edges and Four Corners above 120 seconds to keep the glue fit screen betterWith above Four advices, the screen protector seals and looks great! Perfect fit!Also the price so nice for 2pcs liquid glass! so happy!

  2. Dave

    Is the screen protector a quality product? Absolutely! Does the fingerprint reader work? With no problems whatsoever. Does more information need to be added to the instructions? You betcha!So the issue with my first attempt was, in hindsight, my fault. The table I was using for the phone wasn’t completely level. I put on the liquid “glue” as instructed and it immediately started running towards one end of my phone. I worked my fastest trying to gently hold one end of the phone a smidge higher while unwrapping the cover. By the time I placed the cover on the phone all of the liquid was down at one end and, upon placing the screen protector down, a good dead of it ran off the edge. Nevertheless, I waited to see if there was enough still there to work itself out to the edges and it actually got closer that I thought it would. It took nearly 10 minutes but I was patient and watched it slowly creep to the other end. Finally, with about an inch to go the two sides were filling in faster than the middle and they ended up meeting, forming a huge bubble in the middle. I tried gently pushing, squeegeeing, tapping, etc and finally acknowledged that my first attempt was a waste. I took it off and cleaned everything up to make attempt number two. First, I found a dead-level surface and again, applied all of the liquid. I peeled off the second screen protector and dropped it in to place only to realize that I, perhaps, dropped it too level and didn’t tip it in from one side because from my initial drop, I had air bubbles in the center of the screen. Having no other option/replacement, I finished off the installation and everything went smoothly. The liquid worked it’s way out to the edges without a hitch. I tried tapping/pushing/squeegeeing the screen to see if I could somehow work out those bubbles but they didn’t budge. Knowing I NEEDED a screen protector for my ~$1k phone, I bit the bullet and used the UV light to dry everything up “as-is”. It worked perfectly and I now have a beautifully applied screen protector…. with some bubble right in the middle of the screen. I was able to insert it into my case with no issues just minutes after application. I really want to like this screen protector but, despite the very clear instructional video, some more information needs to be conveyed in it. First, make sure your surface is perfectly level. Second, don’t just drop it straight on to the screen, tip it into place. I’m still up in the air as to whether I’ll drop another $16 to pick up another set or opt to try another options. I’ll update my review if I have another go at this one.

  3. Dejan Andric

    Put this protector few days ago, and all can say, it looks amazing!!!Fingerprint sensor works without any problems, scree looks crystal clear.Followed the instructions, no any problems during the installation.Hope it will stay this way, at the whole great screen protector and it does not cost 55$, as some others.

  4. Bryan Anthony

    The glue won’t hold fully no matter how long I waited and use the blue or purple light on it, I tired both pack out and got the same result and I tired over and hour waiting and then blue lighting it as well. I feel like I wasted my money. I did watch the video on how it is done and I am uselessly okay at installing screen guards. also I installed it with no dust and I still got bubble on the screen that won’t go away. I would return it after waiting an hour of blue lighting it and waiting and screen guard would not fully hold, when I gave up the I tired pulling of the screen guard it cracked really easily.I might have gotten a dud, so you might have better luck then I did.Update: I order more and it worked better but the glue doesn’t hold the edge super when in case and peels a little bit.other then that the, the screen guard looks good and they gave me a refund on the first one to make up for it.

  5. Rocky W

    The best information I can give is practice patience. While the whole install process isn’t long, prepping the phone and waiting for the glue to spread can get you a little antsy. Like other reviewers, please follow the instructions and take your time. Enjoy your purchase, it’s worth it.

  6. Draga T.

    Easy to install, actually works with the fingerprint reader, does NOT look like there is a milky film over your screen (very clear), not expensive.The only thing – I wish it was actually full screen. It does have bent edges that go to the sides, but there is still 2 to 3 millimeters left on all sides (including top and bottom).

  7. Sebastian

    I had purchased another screen protector online for a very low price. (Same system with uv light) and got what i payed for. No instructions and very cheap packaging. Needles to say it was a small learning experience as it also came with no instructions. The video they have here is perfect. Make SURE to squeeze out all the glue in ONE little tube in the center after cleaning the screen AS INSTRUCTED. Adjust a little to fit how u like and dont press down on it. Just apply the uv light. I did indeed have trouble a bit with the finger print reading but i just let it continue curing and yes it did begin slightly working a bit. So i proceeded to make 2 finger prints for my thumb and it seems to just get better as u go.i found that its not the best to press hard but instead to press with a “just right” amaount (if u press too hard ull just flatten your fingerprint and it wont get a proper sonar off ur finger). This product came very well packaged. The screen feels incredibly like the actual screen. I dont write many reviews but im just so satisfied with this one that im happily writings this one. Follow the instruction carefully (they’re here on the listing just look through the pictures) and u should end up with a very very sleek looking phone. If u have fingerprint issue, just wait some time and keep trying at different moments . It took like 6 hours for mine to start working (also try different fingers to kick start the detection. I used my index finger, and then when it read it switched back to my thumb and it kept reading my thumb). Awesome awesome screen protector.

  8. maribel

    I made the mistake to buy a similar glass for $50 with less quality, this product is easy to install if you can get concentrated for 10 minutes, and it looks like if doesn’t have anything, the fingerprint works perfect, and the best they give us 2 glasses.

  9. Emma Taylor

    This is strong fully covered protector that will protect the phone. As you know, now the cell phones are very expensive, so the best way is to get the best screen protector to keep it well, also this is saving money!Since This is the glue liquid tempered glass which it is definitely from the traditional tempered glass, I no any experience to do it.I must admit it took 2 tries to get it right.The 1st time i was failed because i didn’t keep the phone on a very flat surface then caused the liquid to spreading to the end of phone fastly, i noted that was bad so i stopped it soon, because i worried the liquid flow into the charging port! Then i cleaned it with wet wips and dry wipsIt was very luck, This seller offered 2 packso i started my 2nd tempered glass. In order to make sure i can install it sucessfully, i have re-read the guide installation carefully again and watched the video few times and noted all of the warm tipsDo each step As the seller described:- keep my phone on a very flat table;- use the guide sticker to block the ear speaker avoiding the liquid spilling inside; — put the glue on the middle of the screen and wait it fit automatically ( I didn’t move or lift or press glass as the seller mentioned)- the last step, use the UV light to irradiate above 60 seconds including all of edges to keep the glue dry wellAfter all steps, super perfect!! Enjoyed the installation process!!- Zero bubbles!- Super high touch sensitivity- Crystal clear like original glass- Unlock fingerprint- Super beautiful ( i don’t like the traditional tempered glass, super like this liquid tempered glass, really super super beautiful)- Easy to cleanIf you are looking for high quality liquid tempered glass and give your favorite phone a new surface, highly recommend!! This is what you wanna exactlly!!

  10. jmoore

    I am happy enough with this product that I have decided to write my first ever Amazon review. This product is excellent. I have never installed a screen protector that I am truly happy with. No bubbles, no oil slick colors, no alignment issues. Installing was very simple but I would like to point out THE ONLY minor issue I had with the install. I didnt want to wipe the edges of the screen protector (wet glue seeping out) before curing the glue on the main portion of phone screen. I cured the main portion of the screen, wiped the excess glue off of edges. Cured the edges , wiped again and so on and so forth. I used the included light way way more than 60 seconds just to be sure the glue was cured. I tested the thumbprint and it struggled but worked. BUT after re teaching the thumbprint, it seems to work solid. Maybe a tad bit more pressure has to be applied from time to time but it works. I am pretty confident in saying that you wont be disappointed. I spent way too much time and effort trying to find the right screen protector for my new S10+. After reading countless reviews on multiple namebrands, I decided to return the favor by maybe helping someone else make a decision. I did not want to spend 50+ dollars on a screen protector that is the same quality as this one. And that has a “hole” or thin spot in the shape of a circle that allows the thumbprint to work. Oh and lastly , it’s awesome that they give you two screen protectors in the box. With that being said, save the little tab that you pull out of the light so that you can reinsert it for future use 🙂

Add a review

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

You may also like…